Other
Snap-on brake cable guides for bikes that don't have any.
- Steel cable housing guide for 1-1/8" top tubes
- Snaps on; no bolts
- Set of 3 clamps
Avid, Post Bracket, Includes Stainless Caliper Mounting Bolts (CPS and Standard)
The Campagnolo Adjustable U-Shape Spring Support Caliper Brake Part
Campagnolo Return Spring Caliper Brake Part
Campagnolo Power Torque Cup and Bearing Kits
- Fits all Campagnolo Power Torque cranks
- Kit includes 2 bearings and 2 outer seals
Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.
Installation of air volume reducers for Cane Creek shocks make the spring rate more progressive.
- Spacers can be cut to fine-tune spring curve
40-Series Bearing
- Compatible with 110-, 40-, and 10-Series headsets
Replacement top subassemblies are compatible across Cane Creek 110-, 40-, and 10-Series headsets with the same SHIS values.
- Bearings not included
- Stack height: 9mm
40-Series Bearing
- Compatible with 110-, 40-, and 10-Series headsets
These baseplates are the foundation that keeps Chris King headsets turning with legendary smoothness. Manufactured from high-quality stainless steel or titanium, Chris King makes replacement baseplates for all standard sizes and a number of ingenious solutions for those that need something a little special to make their headset work.
- Engineered and manufactured in Portland, Oregon USA
- High-quality stainless steel and titanium baseplates available for all standard Chris King headset sizes
- Titanium baseplates are available in 1-inch and 1 1/8-inch sizes only
- Devolution baseplates are a stainless steel solution that allow King headsets to adapt to a wide variety of steerer tube sizes
- King Stainless Steel baseplates are available in undersized and oversized versions for irregular steerer tube sizes
- 30.0mm ID/40.5mm OD for post-April 1995 1-1/8" Headsets
- 30.0mm ID/44.0mm OD for pre- April 1995 1-1/8" Headsets
Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs.
Includes end cap for 12 x 142 and 12 x 148mm hubs
Fits Shimano 12-speed Micro Spline cassettes
Crafted from lightweight aluminum
Compatible with 12mm thru-axles
Dimension Steerer Extender adds 2 to 3-1/4" height to steerer.
- Extender clamps to steerer; stem clamps to extender
- Adds 2 to 3-1/4-inch height to threadless steerer
- Includes top cap and long bolt
- 40mm of threadless steerer is required for proper installation
- Do not stack steerer extenders; no more than one steerer extender recommended per bike
- WARNING: Dimension Steerer Extender is not recommended for use on forks with carbon fiber steerers
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity
- No retainer means these bearings have 40 percent more capacity
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity
- No retainer means these bearings have 40 percent more capacity
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity
- No retainer means these bearings have 40 percent more capacity
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity
- No retainer means these bearings have 40 percent more capacity
Rebuild seal kits for Fox rear suspension service and repair.
- Includes parts needed for rebuild
FSA Mega Exo Small Parts.
Tight tolerances and precise torque specs mean precision parts like this MegaExo 12 Left Arm Crank Bolt need to be replaced from time to time. Make sure the heart of your drivetrain is secure, and pick up a spare or two today.
FSA Compression Plugs are top assemblies for carbon steerers. Replaces the traditional top cap assembly. Includes cap, bolt, and expander.
- Includes cap, bolt and expander
- Top assembly for carbon steerers replaces traditional top cap and star nut assembly
Jagwire's Brake or Shift Cable Tips are made of lightweight, corrosion-resistant and durable aluminum and are the right size to nicely fit over the ends of up to 1.8mm-diameter cables. These caps are crimped in place on the cables to prevent fraying and ensure your cables last a long time. The tips come in colors to add a little style to your bike.
Page 1 of 5
Next page